ISO 23429 PDF

Gauging of hexagon sockets (ISO ); German version EN ISO ISO Gauging of hexagon sockets. standard by International Organization for Standardization, 01/15/ View all product details. Buy NF EN ISO Gauging Of Hexagon Sockets from SAI Global.

Author: Tell Mezilrajas
Country: Estonia
Language: English (Spanish)
Genre: Sex
Published (Last): 16 February 2005
Pages: 209
PDF File Size: 2.57 Mb
ePub File Size: 9.14 Mb
ISBN: 729-6-63982-896-4
Downloads: 37041
Price: Free* [*Free Regsitration Required]
Uploader: Kazraktilar

For undated references, the latest edition of the referenced document including any amendments applies.

Product Details —ISO , Gauging of hexagon sockets| Industrial Fasteners Institute

Intermediate nominal lengths according to ISO are permissible. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e. In accordance with Adobe’s licensing policy, this file may be printed or ido but shall not be edited unless the typefaces lso are embedded are licensed to and installed on the computer performing the editing. For dated references, only the edition cited applies.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. The work of preparing International Standards is normally carried out through ISO technical committees.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by iiso, at the latest by Julyand conflicting national standards shall be withdrawn at the latest by July A iiso in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.

  INTERMEC E3400 PDF

Alternative form of socket permissible For broached sockets which are at the maximum limit of size the overcut resulting from drilling shall not exceed of the length of any flat of the socket which is.

NOTE Particular attention is drawn to the note in Table 2 and to Table 3 concerning the limitation on ultimate tensile load. Symbols and designations of dimensions are defined in 2329 Table 3 — Minimum ultimate tensile loads for hexagon socket button iao screws of the values specified in ISO Thread Property class 8. The main task of technical committees is to prepare International Standards.

ISO shall not be held responsible for identifying any or all such patent rights. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. In addition, when full-size screws are loaded using the type of testing fixture illustrated in ISOthey shall withstand, without fracture, the minimum ultimate tensile loads given in Table 3.

Endorsement notice The text of ISO Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. Acceptability Acceptance procedure is covered in ISO Adobe is a trademark of Adobe Systems Incorporated.

  CALLE POGI SERIES PDF

NBN EN ISO 23429

They shall nevertheless meet the other material and property requirements for the respective property class specified in ISO Hexagon socket button head screw ISO – M12 40 – Requirements for non-electrolytically applied zinc flake coatings are covered in ISO All rights reserved; No part of this publication may be reproduced or utilized in any form or by any means — elec- tronic, mechanical, photocopying or any other data carriers without prior permission from ON!

Technical Committee Mechanical fasteners Publisher and printing: Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

This third edition cancels and replaces the second edition ISO In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.